• Contact Us: +86 18657466579
  • sales@icseekers.com
  • AD9361BBCZ RF Agile Transceiver Pinout and Pin Functions, Specifications

    2/6/2026 1:11:03 AM

    AD9361BBCZ RF Agile Transceiver Overview

    AD9361BBCZ

    AD9361BBCZ is a highly integrated RF Agile Transceiver™ developed by Analog Devices, designed to support a wide range of wireless communication systems. It integrates dual transmitters and dual receivers, along with high-performance ADCs, DACs, frequency synthesizers, and digital signal conditioning blocks, into a single compact device.

    Covering a broad RF frequency range from 70 MHz to 6.0 GHz, the AD9361BBCZ is widely used in 3G, 4G, and software-defined radio (SDR) platforms. Its flexible architecture allows designers to configure bandwidth, gain, and operating modes entirely through software, significantly reducing development time and system complexity.

    AD9361BBCZ Features

    The AD9361BBCZ combines RF performance with system-level flexibility:
    • RF 2×2 transceiver with integrated 12-bit ADCs and DACs
    • Wide operating frequency range:
      • Receiver: 70 MHz to 6.0 GHz
      • Transmitter: 47 MHz to 6.0 GHz
    • Supports both TDD and FDD operation
    • Tunable channel bandwidth from <200 kHz up to 56 MHz
    • Dual independent direct-conversion receivers
    • Integrated automatic gain control (AGC) and manual gain modes
    • Excellent RF performance with low noise figure and high linearity
    • Integrated fractional-N frequency synthesizers
    • CMOS / LVDS digital interface for baseband connectivity
    • Multichip synchronization support

    These features make the AD9361BBCZ suitable for both commercial and experimental wireless platforms.


    Function Block



    AD9361BBCZ Pinout and Pin Functions

    AD9361BBCZ Pinout


    AD9361BBCZ Pin Functions

    Pin No. Type Mnemonic Description
    A1, A2 I RX2A_N, RX2A_P Receive Channel 2 Differential Input A. Alternatively, each pin can be used as a single-ended input or combined to make a differential pair. Tie unused pins to ground.
    A3, M3 NC NC No Connect. Do not connect to these pins.
    A4, A6, B1, B2, B12, C2, C7 to C12, F3, H2, H3, H6, J2, K2, L2, L3, L7 to L12, M4, M6 I VSSA Analog Ground. Tie these pins directly to the VSSD digital ground on the printed circuit board (one ground plane).
    A5 I TX_MON2 Transmit Channel 2 Power Monitor Input. If this pin is unused, tie it to ground.
    A7, A8 O TX2A_N, TX2A_P Transmit Channel 2 Differential Output A. Tie unused pins to 1.3 V.
    A9, A10 O TX2B_N, TX2B_P Transmit Channel 2 Differential Output B. Tie unused pins to 1.3 V.
    A11 I VDDA1P1_TX_VCO Transmit VCO Supply Input. Connect to B11.
    A12 I TX_EXT_LO_IN External Transmit LO Input. If this pin is unused, tie it to ground.
    B3 O AUXDAC1 Auxiliary DAC 1 Output.
    B4 to B7 O GPO_3 to GPO_0 3.3 V Capable General-Purpose Outputs.
    B8 I VDD_GPO 2.5 V to 3.3 V Supply for the AUXDAC and General-Purpose Output Pins. When the VDD_GPO supply is not used, this supply must be set to 1.3 V.
    B9 I VDDA1P3_TX_LO Transmit LO 1.3 V Supply Input.
    B10 I VDDA1P3_TX_VCO_LDO Transmit VCO LDO 1.3 V Supply Input. Connect to B9.
    B11 O TX_VCO_LDO_OUT Transmit VCO LDO Output. Connect to A11 and a 1 µF bypass capacitor in series with a 1 Ω resistor to ground.
    C1, D1 I RX2C_P, RX2C_N Receive Channel 2 Differential Input C. Each pin can be used as a single-ended input or combined to make a differential pair. These inputs experience degraded performance above 3 GHz. Tie unused pins to ground.
    C3 O AUXDAC2 Auxiliary DAC 2 Output.
    C4 I TEST/ENABLE Test Input. Ground this pin for normal operation.
    C5, C6, D6, D5 I CTRL_IN0 to CTRL_IN3 Control Inputs. Used for manual RX gain and TX attenuation control.
    D2 I VDDA1P3_RX_RF Receiver 1.3 V Supply Input. Connect to D3.
    D3 I VDDA1P3_RX_TX 1.3 V Supply Input.
    D4, E4 to E6, F4 to F6, G4 O CTRL_OUT0, CTRL_OUT1 to CTRL_OUT3, CTRL_OUT6 to CTRL_OUT4, CTRL_OUT7 Control Outputs. These pins are multipurpose outputs that have programmable functionality.
    D7 I/O P0_D9/TX_D4_P Digital Data Port P0/Transmit Differential Input Bus. This is a dual function pin. As P0_D9, it functions as part of the 12-bit bidirectional parallel CMOS level Data Port 0. Alternatively, this pin (TX_D4_P) can function as part of the LVDS 6-bit TX differential input bus with internal LVDS termination.
    D8 I/O P0_D7/TX_D3_P Digital Data Port P0/Transmit Differential Input Bus. This is a dual function pin. As P0_D7, it functions as part of the 12-bit bidirectional parallel CMOS level Data Port 0. Alternatively, this pin (TX_D3_P) can function as part of the LVDS 6-bit TX differential input bus with internal LVDS termination.
    D9 I/O P0_D5/TX_D2_P Digital Data Port P0/Transmit Differential Input Bus. This is a dual function pin. As P0_D5, it functions as part of the 12-bit bidirectional parallel CMOS level Data Port 0. Alternatively, this pin (TX_D2_P) can function as part of the LVDS 6-bit TX differential input bus with internal LVDS termination.
    D10 I/O P0_D3/TX_D1_P Digital Data Port P0/Transmit Differential Input Bus. This is a dual function pin. As P0_D3, it functions as part of the 12-bit bidirectional parallel CMOS level Data Port 0. Alternatively, this pin (TX_D1_P) can function as part of the LVDS 6-bit TX differential input bus with internal LVDS termination.
    D11 I/O P0_D1/TX_D0_P Digital Data Port P0/Transmit Differential Input Bus. This is a dual function pin. As P0_D1, it functions as part of the 12-bit bidirectional parallel CMOS level Data Port 0. Alternatively, this pin (TX_D0_P) can function as part of the LVDS 6-bit TX differential input bus with internal LVDS termination.
    D12, F7, F9, F11, G12, H7, H10, K12 I VSSD Digital Ground. Tie these pins directly to the VSSA analog ground on the printed circuit board (one ground plane).
    E1, F1 I RX2B_P, RX2B_N Receive Channel 2 Differential Input B. Each pin can be used as a single-ended input or combined to make a differential pair. These inputs experience degraded performance above 3 GHz. Tie unused pins to ground.
    E2 I VDDA1P3_RX_LO Receive LO 1.3 V Supply Input.
    E3 I VDDA1P3_TX_LO_BUFFER 1.3 V Supply Input.
    E7 I/O P0_D11/TX_D5_P Digital Data Port P0/Transmit Differential Input Bus. This is a dual function pin. As P0_D11, it functions as part of the 12-bit bidirectional parallel CMOS level Data Port 0. Alternatively, this pin (TX_D5_P) can function as part of the LVDS 6-bit TX differential input bus with internal LVDS termination.
    E8 I/O P0_D8/TX_D4_N Digital Data Port P0/Transmit Differential Input Bus. This is a dual function pin. As P0_D8, it functions as part of the 12-bit bidirectional parallel CMOS level Data Port 0. Alternatively, this pin (TX_D4_N) can function as part of the LVDS 6-bit TX differential input bus with internal LVDS termination.
    E9 I/O P0_D6/TX_D3_N Digital Data Port P0/Transmit Differential Input Bus. This is a dual function pin. As P0_D6, it functions as part of the 12-bit bidirectional parallel CMOS level Data Port 0. Alternatively, this pin (TX_D3_N) can function as part of the LVDS 6-bit TX differential input bus with internal LVDS termination.
    E10 I/O P0_D4/TX_D2_N Digital Data Port P0/Transmit Differential Input Bus. This is a dual function pin. As P0_D4, it functions as part of the 12-bit bidirectional parallel CMOS level Data Port 0. Alternatively, this pin (TX_D2_N) can function as part of the LVDS 6-bit TX differential input bus with internal LVDS termination.
    E11 I/O P0_D2/TX_D1_N Digital Data Port P0/Transmit Differential Input Bus. This is a dual function pin. As P0_D2, it functions as part of the 12-bit bidirectional parallel CMOS level Data Port 0. Alternatively, this pin (TX_D1_N) can function as part of the LVDS 6-bit TX differential input bus with internal LVDS termination.
    E12 I/O P0_D0/TX_D0_N Digital Data Port P0/Transmit Differential Input Bus. This is a dual function pin. As P0_D0, it functions as part of the 12-bit bidirectional parallel CMOS level Data Port 0. Alternatively, this pin (TX_D0_N) can function as part of the LVDS 6-bit TX differential input bus with internal LVDS termination.
    F2 I VDDA1P3_RX_VCO_LDO Receive VCO LDO 1.3 V Supply Input. Connect to E2.
    F8 I/O P0_D10/TX_D5_N Digital Data Port P0/Transmit Differential Input Bus. This is a dual function pin. As P0_D10, it functions as part of the 12-bit bidirectional parallel CMOS level Data Port 0. Alternatively, this pin (TX_D5_N) can function as part of the LVDS 6-bit TX differential input bus with internal LVDS termination.
    F10, G10 I FB_CLK_P, FB_CLK_N Feedback Clock. These pins receive the FB_CLK signal that clocks in TX data. In CMOS mode, use FB_CLK_P as the input and tie FB_CLK_N to ground.
    F12 I VDDD1P3_DIG 1.3 V Digital Supply Input.
    G1 I RX_EXT_LO_IN External Receive LO Input. If this pin is unused, tie it to ground.
    G2 O RX_VCO_LDO_OUT Receive VCO LDO Output. Connect this pin directly to G3 and a 1 渭F bypass capacitor in series with a 1 惟 resistor to ground.
    G3 I VDDA1P1_RX_VCO Receive VCO Supply Input. Connect this pin directly to G2 only.
    G5 I EN_AGC Manual Control Input for Automatic Gain Control (AGC).
    G6 I ENABLE Control Input. This pin moves the device through various operational states.
    G7, G8 O RX_FRAME_N, RX_FRAME_P Receive Digital Data Framing Output Signal. These pins transmit the RX_FRAME signal that indicates whether the RX output data is valid. In CMOS mode, use RX_FRAME_P as the output and leave RX_FRAME_N unconnected.
    G9, H9 I TX_FRAME_P, TX_FRAME_N Transmit Digital Data Framing Input Signal. These pins receive the TX_FRAME signal that indicates when TX data is valid. In CMOS mode, use TX_FRAME_P as the input and tie TX_FRAME_N to ground.
    G11, H11 O DATA_CLK_P, DATA_CLK_N Receive Data Clock Output. These pins transmit the DATA_CLK signal that is used by the BBP to clock RX data. In CMOS mode, use DATA_CLK_P as the output and leave DATA_CLK_N unconnected.
    H1, J1 I RX1B_P, RX1B_N Receive Channel 1 Differential Input B. Alternatively, each pin can be used as a single-ended input. These inputs experience degraded performance above 3 GHz. Tie unused pins to ground.
    H4 I TXNRX Enable State Machine Control Signal. This pin controls the data port bus direction. Logic low selects the RX direction, and logic high selects the TX direction.
    H5 I SYNC_IN Input to Synchronize Digital Clocks Between Multiple AD9361 Devices. If this pin is unused, tied it to ground.
    H8 I/O P1_D11/RX_D5_P Digital Data Port P1/Receive Differential Output Bus. This is a dual function pin. As P1_D11, it functions as part of the 12-bit bidirectional parallel CMOS level Data Port 1. Alternatively, this pin (RX_D5_P) can function as part of the LVDS 6-bit RX differential output bus with internal LVDS termination.
    H12 I VDD_INTERFACE 1.2 V to 2.5 V Supply for Digital I/O Pins (1.8 V to 2.5 V in LVDS Mode).
    J3 I VDDA1P3_RX_SYNTH 1.3 V Supply Input.
    J4 I SPI_DI SPI Serial Data Input.
    J5 I SPI_CLK SPI Clock Input.
    J6 O CLK_OUT Output Clock. This pin can be configured to output either a buffered version of the external input clock, the DCXO, or a divided-down version of the internal ADC_CLK.
    J7 I/O P1_D10/RX_D5_N Digital Data Port P1/Receive Differential Output Bus. This is a dual function pin. As P1_D10, it functions as part of the 12-bit bidirectional parallel CMOS level Data Port 1. Alternatively, this pin (RX_D5_N) can function as part of the LVDS 6-bit RX differential output bus with internal LVDS termination.
    J8 I/O P1_D9/RX_D4_P Digital Data Port P1/Receive Differential Output Bus. This is a dual function pin. As P1_D9, it functions as part of the 12-bit bidirectional parallel CMOS level Data Port 1. Alternatively, this pin (RX_D4_P) can function as part of the LVDS 6-bit RX differential output bus with internal LVDS termination.
    J9 I/O P1_D7/RX_D3_P Digital Data Port P1/Receive Differential Output Bus. This is a dual function pin. As P1_D7, it functions as part of the 12-bit bidirectional parallel CMOS level Data Port 1. Alternatively, this pin (RX_D3_P) can function as part of the LVDS 6-bit RX differential output bus with internal LVDS termination.
    J10 I/O P1_D5/RX_D2_P Digital Data Port P1/Receive Differential Output Bus. This is a dual function pin. As P1_D5, it functions as part of the 12-bit bidirectional parallel CMOS level Data Port 1. Alternatively, this pin (RX_D2_P) can function as part of the LVDS 6-bit RX differential output bus with internal LVDS termination.
    J11 I/O P1_D3/RX_D1_P Digital Data Port P1/Receive Differential Output Bus. This is a dual function pin. As P1_D3, it functions as part of the 12-bit bidirectional parallel CMOS level Data Port 1. Alternatively, this pin (RX_D1_P) can function as part of the LVDS 6-bit RX differential output bus with internal LVDS termination.
    J12 I/O P1_D1/RX_D0_P Digital Data Port P1/Receive Differential Output Bus. This is a dual function pin. As P1_D1, it functions as part of the 12-bit bidirectional parallel CMOS level Data Port 1. Alternatively, this pin (RX_D0_P) can function as part of the LVDS 6-bit RX differential output bus with internal LVDS termination.
    K1, L1 I RX1C_P, RX1C_N Receive Channel 1 Differential Input C. Alternatively, each pin can be used as a single-ended input. These inputs experience degraded performance above 3 GHz. Tie unused pins to ground.
    K3 I VDDA1P3_TX_SYNTH 1.3 V Supply Input.
    K4 I VDDA1P3_BB 1.3 V Supply Input.
    K5 I RESETB Asynchronous Reset. Logic low resets the device.
    K6 I SPI_ENB SPI Enable Input. Set this pin to logic low to enable the SPI bus.
    K7 I/O P1_D8/RX_D4_N Digital Data Port P1/Receive Differential Output Bus. This is a dual function pin. As P1_D8, it functions as part of the 12-bit bidirectional parallel CMOS level Data Port 1. Alternatively, this pin (RX_D4_N) can function as part of the LVDS 6-bit RX differential output bus with internal LVDS termination.
    K8 I/O P1_D6/RX_D3_N Digital Data Port P1/Receive Differential Output Bus. This is a dual function pin. As P1_D6, it functions as part of the 12-bit bidirectional parallel CMOS level Data Port 1. Alternatively, this pin (RX_D3_N) can function as part of the LVDS 6-bit RX differential output bus with internal LVDS termination.
    K9 I/O P1_D4/RX_D2_N Digital Data Port P1/Receive Differential Output Bus. This is a dual function pin. As P1_D4, it functions as part of the 12-bit bidirectional parallel CMOS level Data Port 1. Alternatively, this pin (RX_D2_N) can function as part of the LVDS 6-bit RX differential output bus with internal LVDS termination.
    K10 I/O P1_D2/RX_D1_N Digital Data Port P1/Receive Differential Output Bus. This is a dual function pin. As P1_D2, it functions as part of the 12-bit bidirectional parallel CMOS level Data Port 1. Alternatively, this pin (RX_D1_N) can function as part of the LVDS 6-bit RX differential output bus with internal LVDS termination.
    K11 I/O P1_D0/RX_D0_N Digital Data Port P1/Receive Differential Output Bus. This is a dual function pin. As P1_D0, it functions as part of the 12-bit bidirectional parallel CMOS level Data Port 1. Alternatively, this pin (RX_D0_N) can function as part of the LVDS 6-bit RX differential output bus with internal LVDS termination.
    L4 I RBIAS Bias Input Reference. Connect this pin through a 14.3  kΩ (1% tolerance) resistor to ground.
    L5 I AUXADC Auxiliary ADC Input. If this pin is unused, tie it to ground.
    L6 O SPI_DO SPI Serial Data Output in 4-Wire Mode, or High-Z in 3-Wire Mode.
    M1, M2 I RX1A_P, RX1A_N Receive Channel 1 Differential Input A. Alternatively, each pin can be used as a single-ended input. Tie unused pins to ground.
    M5 I TX_MON1 Transmit Channel 1 Power Monitor Input. When this pin is unused, tie it to ground.
    M7, M8 O TX1A_P, TX1A_N Transmit Channel 1 Differential Output A. Tie unused pins to 1.3 V.
    M9, M10 O TX1B_P, TX1B_N Transmit Channel 1 Differential Output B. Tie unused pins to 1.3 V.
    M11, M12 I XTALP, XTALN Reference Frequency Crystal Connections. When a crystal is used, connect it between these two pins. When an external clock source is used, connect it to XTALN and leave XTALP unconnected.

    AD9361BBCZ  Specifications

    Attribute Value
    Brand: Analog Devices
    Product Category: RF Transceiver
    RoHS: Yes
    Type: LTE, WiMAX
    Frequency Range: 70 MHz to 6 GHz
    Modulation Format: 64-QAM
    Supply Voltage - Min: 1.267 V
    Supply Voltage - Max: 1.33 V
    Output Power: 8 dBm
    Minimum Operating Temperature: - 40 C
    Maximum Operating Temperature: + 85 C
    Interface Type: 3-Wire, 4-Wire, SPI
    Package/Case: BGA-144
    Number of Receivers: 2
    Number of Transmitters: 2
    Product Type: RF Transceiver
    Sensitivity: 2.5 dB
    Series: AD9361
    184
    Subcategory: Wireless & RF Integrated Circuits
    Technology: Si
    Tradename: RadioVerse

    Application Scenarios

    Thanks to its wide frequency coverage and software configurability, the AD9361BBCZ is used in a variety of wireless applications:
    • Software-defined radio (SDR) platforms
    • 3G / 4G LTE base stations and small cells
    • Femtocell, picocell, and microcell systems
    • Point-to-point and point-to-multipoint radio links
    • Wireless test equipment and RF prototyping
    • Research, education, and experimental RF platforms
    Its flexibility makes it especially popular in both commercial deployments and advanced RF development environments.

    Inventory and Pricing

    AD9361BBCZ  38 In stock


    Copyright © 2025 Xinhou Future Technology Co., Limited

    Home

    Home

    Product

    Product

    Phone

    Phone

    About Us

    About Us